Paragon Brakes 2-Piece Rear 380mm x 30mm Rotors w/ Black Hard Anodized Hat Nissan GT-R R35 2008+

Made of CM-250 special formulated high carbon alloy cast iron, it allows for an optimal bite, thermal characteristics, high-temperature strength and durability. Rotor rings are heat treated to release stress in the rotor to avoid deformation and vibration then turned by state-of-the-art CBN surface machining to ensure better break-in with new brake pads.

Vibration is reduced as the rotor lateral run-out is kept within 0.03mm and well-balanced: variations are kept within 2 grams. All rotors went through rigorous quality control procedures and inspections to ensure the rotors are fit for their purposes. The fully-floating 2-piece design allows thermal expansion of the rotor while minimizing deformation and ensuring the rotor is self-centered with the pads. A slotted rotor improves braking consistency by maintaining a clean contact surface and dissipate heat generated and gases released when the pads come into contact with the rotors. Slotted rotors have a superior advantage over blank rotors in wet or raining conditions by preventing water films to form between the brake pad and rotor surface. Weighing less than most O.E. rotors while maintaining proper thermal capacity, our 2-piece rotors improves overall handling by saving unsprung mass.

Aluminum hats are CNC machined from lightweight 6061-T6 aerospace grade aluminum for high strength and durability under extreme track conditions, then black hard coat/hard anodized to increase resistance to wear and corrosion. Mil-spec Type III anodized hats will not discolor under extreme heat, and are harder and more wear/scratch resistant. Unnecessary materials are taken out from the aluminum hats for maximum weight savings while maintaining proper structural integrity. Black hard coat and hard coat anodized hats are the same in terms of performance and durability.

Due to heavy vehicle weight and absence of effective brake cooling system, cracking on OEM GT-R rotors are common especially in areas around the cross drilled holes. Paragon Performance rotors can be an effective solution to this issue while improving pedal feel and brake modulation.

Features :

• Direct bolt-on without any modifications and designed to work flawlessly with OEM ABS and brake system while maintaining factory brake bias. Compatible with OEM brake pads or aftermarket pads with the same pad depth (D)
• Directional ventilation vanes for optimal cooling performance, runs up to 30% cooler than O.E. rotors and increase cooling efficiency by up to 30%
• Fully-floating 2-piece design
• Utilizes OEM E-brake by integrating iron sleeve into aluminum hat
• Minimizing brake fade & judder during extended sessions
• Rotor to hat mounting system: H-Bobbin (8 bolt)
• Weighs 24.6 lbs (11.16 kg)
• Great upgrade from non-directional, pillar vane OEM rotors

Specifications :

• Diameter: 380mm (14.96")
• Thickness (new): 30mm (1.18")
• Thickness (min.): 28mm (1.10")
• Type: 2-piece floating
• Face Pattern: Slotted
• Vented / Solid: Directional ventilated
• Number of Vanes: 48
• Hat Material: 6061-T6 Aluminum w/ integrated iron sleeve for e-brake
• Friction Ring Material: CM-250 high carbon alloy cast iron
• Rotor Finish: CBN turned
• Weight (per rotor): 24.6 lbs (11.16 kg)

Includes :

• One pair of Paragon Performance 380mm x 30mm (14.96" x 1.18") 2-piece rotor assemblies with black hard coat/hard anodized 6061-T6 aerospace grade aluminum hats, stainless steel bobbins, and anti-rattle clips (assembled and ready to install)
• Detailed installation manual

Install Instructions :

• For 2-Piece Rotor Instructions CLICK HERE
• For Track Performance Big Brake Kit Instructions CLICK HERE

Fitments :

• Nissan GT-R R35 2008+

⚠WARNING: Cancer and Reproductive Harm
https://www.P65Warnings.ca.gov