Wisefab Lock Kit with Rack Offset Spacers Nissan S14 V2 1995-1998

$2,250.00 USD

Select your vehicle to confirm fit

Wisefab – Bushings. Fits Nissan 240SX / Silvia S14.

  • Made to order — subject to stock confirmation.
  • Your card is authorized now, charged only once we confirm stock (usually within 24 hours).
  • Ships from our Wisconsin warehouse. Delivery 3–7 business days.
  • Ships direct from our supplier network — delivery depends on supplier availability.
  • Not sure it fits? Ask us →
Wisefab Nissan S14 angle kit with rack offset spacers has two major upgrades. The knuckle has been designed to allow more suspension travel with the trending long stroke coilovers. Lower control arm has been redesigned for more convenient alignment setup. The result was more grip at the front and more precise steering. This will give you the competitive edge. All the parts in the Nissan S14 angle kit are provided as spare parts.

S13 kit is for the 4 lug spindle, if you have 5 lug on your S13 please select the Nissan S13 Angle kit with rack offset spacers

Camber: -4 +/-0,5
Caster: 3,5 +/-0,5

Product Details:

  • More usable lock.
  • 65+ degrees of lock, better feel and precise handling. You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment.
  • Ackermann adjustment kit included.
  • Less sensitive steering.
  • Increased steering ratio for smooth handling.
  • More suspension travel.
  • Less interference risk at full droop. Longstroke coilover kits can be used.
  • Lighter and stronger.
  • Optimized design in combination with high strenght steel is used.
  • Higher roll center (RC).
  • On Wisefab knuckle, the ball joint is lowered 60mm, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles.
  • Adjustable camber and caster with adjustable doubleplates.
  • Adjustable lock stopper.
  • One piece lower control arm desing.
  • Lower links are replaced with one arm. Drifting with higher steering angle the stiffness and packaging would become an issue. Therefore lower one piece arm is used.
  • Very good camber control and minimal bump steer with high steering angles.
  • On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
    • Steering jacking control.
    • During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.
    • Consistent and predictable self-alignment torque.
    • Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock.

Kit Details:

  • Adjustable coilover upper mounts, Formula Drift compliance.
  • Knuckles with hardware.
  • Lower control arms.
  • Assembeled tie rods.
  • Rack offset kit.
  • Rack installation guide.
  • Installation guide.

Fitment:

  • Nissan S14 V2 1995-1998
Proposition 65

âš WARNING: Cancer and Reproductive Harm
https://www.P65Warnings.ca.gov

Fitment: Nissan 240SX / Silvia S14 (1995-1998) KA24DE / SR20DET (JDM)

Please confirm year, trim and engine before ordering.

Shop by vehicle

Pick your car once — we’ll only show parts that fit.

Popular makes